NSE8_812 Tested & Approved Fortinet Network Security Expert Study Materials
Validate your Skills with Updated Fortinet Network Security Expert Exam Questions & Answers and Test Engine
Fortinet NSE8_812 certification is recognized globally as a mark of proficiency in advanced network security. Fortinet NSE 8 - Written Exam (NSE8_812) certification is particularly useful for network security professionals who are responsible for designing, implementing, and managing complex security infrastructures for large organizations. With the NSE 8 certification, professionals can demonstrate their expertise in advanced network security and gain a competitive advantage in their careers.
NEW QUESTION # 23
Refer to the exhibits.
A customer wants to deploy 12 FortiAP 431F devices on high density conference center, but they do not currently have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy From the FortiSwitch models and sample retail prices shown in the exhibit, which build of materials would have the lowest cost, while fulfilling the customer's requirements?
- A. 2x FortiSwitch 224E-POE
- B. 2x FortiSwitch 248E-FPOE
- C. 1x FortiSwitch 248EFPOE
- D. 2x FortiSwitch 124E-FPOE
Answer: B
Explanation:
The customer wants to deploy 12 FortiAP 431F devices on a high density conference center, but they do not have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy. PoE switches are switches that can provide both data and power to connected devices over Ethernet cables, eliminating the need for separate power adapters or outlets. PoE switches are useful for deploying devices such as wireless access points, IP cameras, and VoIP phones in locations where power outlets are scarce or inconvenient. The FortiAP 431F is a wireless access point that supports PoE+ (IEEE 802.3at) standard, which can deliver up to 30W of power per port. The FortiAP 431F has a maximum power consumption of 25W when running at full power. Therefore, to run 12 FortiAP 431F devices at full power, the customer needs PoE switches that can provide at least 300W of total PoE power budget (25W x 12). The customer also needs network redundancy, which means that they need at least two PoE switches to connect the FortiAP devices in case one switch fails or loses power. From the FortiSwitch models and sample retail prices shown in the exhibit, the build of materials that has the lowest cost while fulfilling the customer's requirements is 2x FortiSwitch 248E-FPOE. The FortiSwitch 248E-FPOE is a PoE switch that has 48 GE ports with PoE+ capability and a total PoE power budget of 370W. It also has 4x 10 GE SFP+ uplink ports for high-speed connectivity. The sample retail price of the FortiSwitch 248E-FPOE is $1,995, which means that two units will cost $3,990. This is the lowest cost among the other options that can meet the customer's requirements. Option A is incorrect because the FortiSwitch 248EFPOE is a non-PoE switch that has no PoE capability or power budget. It cannot provide power to the FortiAP devices over Ethernet cables. Option B is incorrect because the FortiSwitch 224E-POE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Option D is incorrect because the FortiSwitch 124E-FPOE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Reference: https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiSwitch_Secure_Access_Series.pdf https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiAP_400_Series.pdf
NEW QUESTION # 24
You are creating the CLI script to be used on a new SD-WAN deployment You will have branches with a different number of internet connections and want to be sure there is no need to change the Performance SLA configuration in case more connections are added to the branch.
The current configuration is:
Which configuration do you use for the Performance SLA members?
- A. set members all
- B. set members any
- C. set members 0
- D. current configuration already fulfills the requirement
Answer: B
Explanation:
The set members any option will ensure that all of the SD-WAN interfaces are included in the Performance SLA. This is the best option if you want to be sure that the Performance SLA will be triggered even if more connections are added to the branch in the future.
The set members 0 option will exclude all of the SD-WAN interfaces from the Performance SLA. This is not a good option because it will prevent the Performance SLA from being triggered even if there is a problem with the network.
The current configuration already fulfills the requirement option is incorrect because it does not ensure that all of the SD-WAN interfaces will be included in the Performance SLA.
The set members all option will include all of the SD-WAN interfaces in the Performance SLA, but it is not the best option because it is not scalable. If you have a large number of SD-WAN interfaces, this option will cause the Performance SLA to be triggered too often.
References:
Performance SLA | FortiGate / FortiOS 7.4.0
Configuring Performance SLA | FortiGate / FortiOS 7.4.0
NEW QUESTION # 25
You are deploying a FortiExtender (FEX) on a FortiGate-60F. The FEX will be managed by the FortiGate. You anticipate high utilization. The requirement is to minimize the overhead on the device for WAN traffic.
Which action achieves the requirement in this scenario?
- A. Enable CAPWAP connectivity between the FortiGate and the FortiExtender.
- B. Add a VLAN under the FEX-WAN interface on the FortiGate.
- C. Change connectivity between the FortiGate and the FortiExtender to use VLAN Mode
- D. Add a switch between the FortiGate and FEX.
Answer: A
Explanation:
The FortiExtender (FEX) is a device that provides wireless WAN connectivity for FortiGate devices by using 3G/4G/LTE cellular networks. The FEX can be managed by the FortiGate device that it connects to, or by a FortiManager device in a centralized management scenario. The FEX can use either Ethernet or CAPWAP connectivity to communicate with the FortiGate device. Ethernet connectivity means that the FEX uses a standard Ethernet connection to send and receive data packets from the FortiGate device. CAPWAP connectivity means that the FEX uses a Control And Provisioning of Wireless Access Points (CAPWAP) tunnel to encapsulate data packets and send them over an IP network to the FortiGate device. If the requirement is to minimize the overhead on the device for WAN traffic, one option is to enable CAPWAP connectivity between the FortiGate and the FEX. This option can reduce the overhead on the device by offloading some of the processing tasks from the CPU to the NP6 processor, which can handle CAPWAP traffic more efficiently than Ethernet traffic. This option can also provide more flexibility and scalability for WAN traffic by allowing multiple FEX devices to connect to a single FortiGate device over an IP network. Reference: https://docs.fortinet.com/document/fortigate/7.0.0/cookbook/19662/configuring-fortigate-with-fortiextender https://docs.fortinet.com/document/fortigate/7.0.0/cookbook/19662/capwap-connectivity
NEW QUESTION # 26
A remote IT Team is in the process of deploying a FortiGate in their lab. The closed environment has been configured to support zero-touch provisioning from the FortiManager, on the same network, via DHCP options. After waiting 15 minutes, they are reporting that the FortiGate received an IP address, but the zero-touch process failed.
The exhibit below shows what the IT Team provided while troubleshooting this issue:
Which statement explains why the FortiGate did not install its configuration from the FortiManager?
- A. The DHCP server used the incorrect option type for the FortiManager IP address.
- B. The FortiGate was not configured with the correct pre-shared key to connect to the FortiManager
- C. The configuration was modified on the FortiGate prior to connecting to the FortiManager
- D. The DHCP server was not configured with the FQDN of the FortiManager
Answer: A
Explanation:
C is correct because the DHCP server used the incorrect option type for the FortiManager IP address. The option type should be 43 instead of 15, as shown in the FortiManager Administration Guide under Zero-Touch Provisioning > Configuring DHCP options for ZTP. References: https://docs.fortinet.com/document/fortimanager/7.4.0/administration-guide/568591/high-availability https://docs.fortinet.com/document/fortimanager/7.4.0/administration-guide/568591/high-availability/568592/configuring-ha-options
NEW QUESTION # 27
Which two statements are correct on a FortiGate using the FortiGuard Outbreak Protection Service (VOS)? (Choose two.)
- A. The AV engine scan must be enabled to use the FortiGuard VOS feature
- B. If third-party AV database returns a match the scanned file is deemed to be malicious.
- C. The antivirus database queries FortiGuard with the hash of a scanned file
- D. The FortiGuard VOS can be used only with proxy-base policy inspections.
- E. The hash signatures are obtained from the FortiGuard Global Threat Intelligence database.
Answer: C,E
Explanation:
The FortiGuard Outbreak Prevention Service (VOS) is a feature that enhances the antivirus scanning capabilities of FortiGate by querying FortiGuard with the hash of a scanned file that is not found in the local antivirus database. If the hash matches a signature in the FortiGuard Global Threat Intelligence database, which contains information about known malware and zero-day threats, the file is deemed to be malicious and blocked by FortiGate. The VOS feature can be used with both proxy-based and flow-based policy inspections, and does not require the AV engine scan to be enabled. Reference: https://docs.fortinet.com/document/fortigate/6.2.14/cookbook/968606/outbreak-prevention-service
NEW QUESTION # 28
Refer to the exhibits.
A customer wants to deploy 12 FortiAP 431F devices on high density conference center, but they do not currently have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy From the FortiSwitch models and sample retail prices shown in the exhibit, which build of materials would have the lowest cost, while fulfilling the customer's requirements?
- A. 2x FortiSwitch 224E-POE
- B. 2x FortiSwitch 248E-FPOE
- C. 1x FortiSwitch 248EFPOE
- D. 2x FortiSwitch 124E-FPOE
Answer: B
Explanation:
The customer wants to deploy 12 FortiAP 431F devices on a high density conference center, but they do not have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy. PoE switches are switches that can provide both data and power to connected devices over Ethernet cables, eliminating the need for separate power adapters or outlets. PoE switches are useful for deploying devices such as wireless access points, IP cameras, and VoIP phones in locations where power outlets are scarce or inconvenient. The FortiAP 431F is a wireless access point that supports PoE+ (IEEE 802.3at) standard, which can deliver up to 30W of power per port. The FortiAP 431F has a maximum power consumption of 25W when running at full power. Therefore, to run 12 FortiAP 431F devices at full power, the customer needs PoE switches that can provide at least 300W of total PoE power budget (25W x 12). The customer also needs network redundancy, which means that they need at least two PoE switches to connect the FortiAP devices in case one switch fails or loses power. From the FortiSwitch models and sample retail prices shown in the exhibit, the build of materials that has the lowest cost while fulfilling the customer's requirements is 2x FortiSwitch 248E-FPOE. The FortiSwitch 248E-FPOE is a PoE switch that has 48 GE ports with PoE+ capability and a total PoE power budget of 370W. It also has 4x 10 GE SFP+ uplink ports for high-speed connectivity. The sample retail price of the FortiSwitch 248E-FPOE is $1,995, which means that two units will cost $3,990. This is the lowest cost among the other options that can meet the customer's requirements. Option A is incorrect because the FortiSwitch 248EFPOE is a non-PoE switch that has no PoE capability or power budget. It cannot provide power to the FortiAP devices over Ethernet cables. Option B is incorrect because the FortiSwitch 224E-POE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Option D is incorrect because the FortiSwitch 124E-FPOE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. References: https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiSwitch_Secure_Access_Series.pdf https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiAP_400_Series.pdf
NEW QUESTION # 29
Refer to the exhibits.
A FortiGate cluster (CL-1) protects a data center hosting multiple web applications. A pair of FortiADC devices are already configured for SSL decryption (FAD-1), and re-encryption (FAD-2). CL-1 must accept unencrypted traffic from FAD-1, perform application detection on the plain-text traffic, and forward the inspected traffic to FAD-2.
The SSL-Offload-App-Detect application list and SSL-Offload protocol options profile are applied to the firewall policy handling the web application traffic on CL-1.
Given this scenario, which two configuration tasks must the administrator perform on CL-1? (Choose two.) A)
B)
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: A,C
Explanation:
To enable application detection on plain-text traffic that has been decrypted by FortiADC, the administrator must perform two configuration tasks on CL-1:
Enable SSL offloading in the firewall policy and select the SSL-Offload protocol options profile.
Enable application control in the firewall policy and select the SSL-Offload-App-Detect application list. References: https://docs.fortinet.com/document/fortigate/6.4.0/cookbook/103438/application-detection-on-ssl-offloaded-traffic
NEW QUESTION # 30
An administrator has configured a FortiGate device to authenticate SSL VPN users using digital certificates. A FortiAuthenticator is the certificate authority (CA) and the Online Certificate Status Protocol (OCSP) server.
Part of the FortiGate configuration is shown below:
Based on this configuration, which two statements are true? (Choose two.)
- A. OCSP checks will always go to the configured FortiAuthenticator
- B. OCSP certificate responses are never cached by the FortiGate.
- C. The OCSP check of the certificate can be combined with a certificate revocation list.
- D. If the OCSP server is unreachable, authentication will succeed if the certificate matches the CA.
Answer: A,D
Explanation:
A is correct because the OCSP server is configured as the FortiAuthenticator in the config vpn certificate ocsp-server section. D is correct because the config vpn ssl settings section has set ocsp-option to allow. This means that if the OCSP server is unreachable, authentication will succeed if the certificate matches the CA. Reference: https://docs.fortinet.com/document/fortigate/7.0.1/administration-guide/490351/ssl-vpn-authentication https://docs.fortinet.com/document/fortigate/7.4.0/administration-guide/266506/ssl-vpn-with-certificate-authentication
NEW QUESTION # 31
A customer wants to use the FortiAuthenticator REST API to retrieve an SSO group called SalesGroup. The following API call is being made with the 'curl' utility:
Which two statements correctly describe the expected behavior of the FortiAuthenticator REST API? (Choose two.)
- A. Only users with the "Full permission" role can access the REST API
- B. If the REST API web service access key is lost, it cannot be retrieved and must be changed.
- C. This API call will fail because it requires that API version 2
- D. The syntax is incorrect because the API calls needs the get method.
Answer: C,D
Explanation:
To retrieve an SSO group called SalesGroup using the FortiAuthenticator REST API, the following issues need to be fixed in the API call:
The API version should be v2, not v1, as SSO groups are only supported in version 2 of the REST API.
The HTTP method should be GET, not POST, as GET is used to retrieve information from the server, while POST is used to create or update information on the server. Therefore, a correct API call would look like this: curl -X GET -H "Authorization: Bearer <token>" https://fac.example.com/api/v2/sso/groups/SalesGroup References: https://docs.fortinet.com/document/fortiauthenticator/6.4.1/rest-api-solution-guide/927310/introduction https://docs.fortinet.com/document/fortiauthenticator/6.4.1/rest-api-solution-guide/927311/sso-groups
NEW QUESTION # 32
Refer to the exhibit containing the configuration snippets from the FortiGate. Customer requirements:
* SSLVPN Portal must be accessible on standard HTTPS port (TCP/443)
* Public IP address (129.11.1.100) is assigned to portl
* Datacenter.acmecorp.com resolves to the public IP address assigned to portl The customer has a Let's Encrypt certificate that is going to expire soon and it reports that subsequent attempts to renew that certificate are failing.
Reviewing the requirement and the exhibit, which configuration change below will resolve this issue?
A)
B)
C)
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: A
Explanation:
The customer's SSLVPN Portal is currently configured to use a self-signed certificate. This means that the certificate is not trusted by any browsers, and users will have to accept a security warning before they can connect to the portal.
To resolve this issue, the customer needs to configure the FortiGate to use a Let's Encrypt certificate. Let's Encrypt is a free certificate authority that provides trusted certificates for websites and other applications.
The configuration change in option B will configure the FortiGate to use a Let's Encrypt certificate for the SSLVPN Portal. This will allow users to connect to the portal without having to accept a security warning.
The other configuration changes are not necessary to resolve the issue. Option A will configure the FortiGate to use a different port for the SSLVPN Portal, but this will not resolve the issue with the self-signed certificate. Option C will configure the FortiGate to use a different DNS name for the SSLVPN Portal, but this will also not resolve the issue with the self-signed certificate. Option D will configure the FortiGate to use a different certificate authority for the SSLVPN Portal, but this will also not resolve the issue because the customer still needs to use a trusted certificate.
References:
Configuring SSLVPN with Let's Encrypt: https://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/822087/acme-certificate-support Let's Encrypt: https://letsencrypt.org/
NEW QUESTION # 33
You must configure an environment with dual-homed servers connected to a pair of FortiSwitch units using an MCLAG.
Multicast traffic is expected in this environment, and you should ensure unnecessary traffic is pruned from links that do not have a multicast listener.
In which two ways must you configure the igmps-f lood-traffic and igmps-flood-report settings? (Choose two.)
- A. disable on ICL trunks
- B. disable on the ISL and FortiLink trunks
- C. enable on the ISL and FortiLink trunks
- D. enable on ICL trunks
Answer: A,B
Explanation:
A is correct because disabling igmps-flood-traffic and igmps-flood-report on ICL trunks prevents unnecessary multicast traffic from being flooded across the MCLAG cluster members. C is correct because disabling igmps-flood-traffic and igmps-flood-report on the ISL and FortiLink trunks prevents unnecessary multicast traffic from being flooded to other switches or FortiGates that do not have multicast listeners. Reference: https://docs.fortinet.com/document/fortiswitches/6.4.0/administration-guide/381057/multicast-forwarding https://docs.fortinet.com/document/fortiswitches/6.4.0/administration-guide/381057/multicast-forwarding/381058/configuring-multicast-forwarding
NEW QUESTION # 34
Refer to the CLI output:
Given the information shown in the output, which two statements are correct? (Choose two.)
- A. Reputation from blacklisted IP addresses from DHCP or PPPoE pools can be restored
- B. The IP Reputation feature has been manually updated
- C. Geographical IP policies are enabled and evaluated after local techniques.
- D. An IP address that was previously used by an attacker will always be blocked
- E. Attackers can be blocked before they target the servers behind the FortiWeb.
Answer: A,E
Explanation:
The CLI output shown in the exhibit indicates that FortiWeb has enabled IP Reputation feature with local techniques enabled and geographical IP policies enabled after local techniques (set geoip-policy-order after-local). IP Reputation feature is a feature that allows FortiWeb to block or allow traffic based on the reputation score of IP addresses, which reflects their past malicious activities or behaviors. Local techniques are methods that FortiWeb uses to dynamically update its own blacklist based on its own detection of attacks or violations from IP addresses (such as signature matches, rate limiting, etc.). Geographical IP policies are rules that FortiWeb uses to block or allow traffic based on the geographical location of IP addresses (such as country, region, city, etc.). Therefore, based on the output, one correct statement is that attackers can be blocked before they target the servers behind the FortiWeb. This is because FortiWeb can use IP Reputation feature to block traffic from IP addresses that have a low reputation score or belong to a blacklisted location, which prevents them from reaching the servers and launching attacks. Another correct statement is that reputation from blacklisted IP addresses from DHCP or PPPoE pools can be restored. This is because FortiWeb can use local techniques to remove IP addresses from its own blacklist if they stop sending malicious traffic for a certain period of time (set local-techniques-expire-time), which allows them to regain their reputation and access the servers. This is useful for IP addresses that are dynamically assigned by DHCP or PPPoE and may change frequently. References: https://docs.fortinet.com/document/fortiweb/6.4.0/administration-guide/19662/ip-reputation https://docs.fortinet.com/document/fortiweb/6.4.0/administration-guide/19662/geographical-ip-policies
NEW QUESTION # 35
Refer to the exhibit.
A customer has deployed a FortiGate 300E with virtual domains (VDOMs) enabled in the multi-VDOM mode. There are three VDOMs: Root is for management and internet access, while VDOM 1 and VDOM 2 are used for segregating internal traffic. AccountVInk and SalesVInk are standard VDOM links in Ethernet mode.
Given the exhibit, which two statements below about VDOM behavior are correct? (Choose two.)
- A. The VDOM links are in Ethernet mode because they have IP addressed assigned on both sides.
- B. Traffic on AccountVInk and SalesVInk will not be accelerated.
- C. OSPF routing can be configured between VDOM 1 and Root VDOM without any configuration changes to AccountVInk
- D. You can apply OSPF routing on the VDOM link in either PPP or Ethernet mode
- E. Root VDOM is an Admin type VDOM, while VDOM 1 and VDOM 2 are Traffic type VDOMs.
Answer: D,E
Explanation:
a) You can apply OSPF routing on the VDOM link in either PPP or Ethernet mode. This is because VDOM links can be configured in either PPP or Ethernet mode, and OSPF routing can be configured on both types of links.
d) Root VDOM is an Admin type VDOM, while VDOM 1 and VDOM 2 are Traffic type VDOMs. This is because the Root VDOM is the default VDOM, and it is used for management and internet access. VDOM 1 and VDOM 2 are traffic type VDOMs, which are used for segregating internal traffic.
The other options are not correct.
b) Traffic on AccountVInk and SalesVInk will not be accelerated. This is because VDOM links are not accelerated by default. However, you can configure acceleration on VDOM links if you want.
c) The VDOM links are in Ethernet mode because they have IP addressed assigned on both sides. This is not necessarily true. The VDOM links could be in PPP mode even if they have IP addresses assigned on both sides.
e) OSPF routing can be configured between VDOM 1 and Root VDOM without any configuration changes to AccountVInk. This is correct. OSPF routing can be configured between any two VDOMs, even if they are not directly connected. In this case, the OSPF routing would be configured on the AccountVInk link.
NEW QUESTION # 36
A customer's cybersecurity department needs to implement security for the traffic between two VPCs in AWS, but these belong to different departments within the company. The company uses a single region for all their VPCs.
Which two actions will achieve this requirement while keeping separate management of each department's VPC? (Choose two.)
- A. Migrate all the instances to the same VPC and create 1AM accounts for each department, then implement a new subnet for a FortiGate auto-scaling group and use routing tables to force the traffic through the FortiGate cluster.
- B. Create a transit VPC with a FortiGate HA cluster, connect to the other two using VPC peering, and use routing tables to force traffic through the FortiGate cluster.
- C. Create an 1AM account for the cybersecurity department to manage both existing VPC, create a FortiGate HA Cluster on each VPC and IPSEC VPN to force traffic between the VPCs through the FortiGate clusters
- D. Create a VPC with a FortiGate auto-scaling group with a Transit Gateway attached to the three VPC to force routing through the FortiGate cluster
Answer: B,D
Explanation:
To implement security for the traffic between two VPCs in AWS, while keeping separate management of each department's VPC, two possible actions are:
Create a transit VPC with a FortiGate HA cluster, connect to the other two using VPC peering, and use routing tables to force traffic through the FortiGate cluster. This option allows the cybersecurity department to manage the transit VPC and apply security policies on the FortiGate cluster, while the other departments can manage their own VPCs and instances. The VPC peering connections enable direct communication between the VPCs without using public IPs or gateways. The routing tables can be configured to direct all inter-VPC traffic to the transit VPC.
Create a VPC with a FortiGate auto-scaling group with a Transit Gateway attached to the three VPCs to force routing through the FortiGate cluster. This option also allows the cybersecurity department to manage the security VPC and apply security policies on the FortiGate cluster, while the other departments can manage their own VPCs and instances. The Transit Gateway acts as a network hub that connects multiple VPCs and on-premises networks. The routing tables can be configured to direct all inter-VPC traffic to the security VPC. Reference: https://docs.fortinet.com/document/fortigate-public-cloud/7.2.0/aws-administration-guide/506140/connecting-a-local-fortigate-to-an-aws-vpc-vpn https://docs.fortinet.com/document/fortigate-public-cloud/7.0.0/sd-wan-architecture-for-enterprise/166334/sd-wan-configuration
NEW QUESTION # 37
Refer to the exhibits, which show a firewall policy configuration and a network topology.
An administrator has configured an inbound SSL inspection profile on a FortiGate device (FG-1) that is protecting a data center hosting multiple web pages-Given the scenario shown in the exhibits, which certificate will FortiGate use to handle requests to xyz.com?
- A. FortiGate will fall-back to the default Fortinet_CA_SSL certificate.
- B. FortiGate will reject the connection since no certificate is defined.
- C. FortiGate will use the Fortinet_CA_Untrusted certificate for the untrusted connection,
- D. FortiGate will use the first certificate in the server-cert list-the abc.com certificate
Answer: A
Explanation:
When using inbound SSL inspection, FortiGate needs to present a certificate to the client that matches the requested domain name. If no matching certificate is found in the server-cert list, FortiGate will fall-back to the default Fortinet_CA_SSL certificate, which is self-signed and may trigger a warning on the client browser. Reference: https://docs.fortinet.com/document/fortigate/6.4.0/cookbook/103437/inbound-ssl-inspection
NEW QUESTION # 38
Refer to the exhibit containing the configuration snippets from the FortiGate. Customer requirements:
* SSLVPN Portal must be accessible on standard HTTPS port (TCP/443)
* Public IP address (129.11.1.100) is assigned to portl
* Datacenter.acmecorp.com resolves to the public IP address assigned to portl The customer has a Let's Encrypt certificate that is going to expire soon and it reports that subsequent attempts to renew that certificate are failing.
Reviewing the requirement and the exhibit, which configuration change below will resolve this issue?
A)
B)
C)
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: B
Explanation:
To resolve the issue of failing to renew the Let's Encrypt certificate, the configuration change that is needed is to enable the HTTP-to-HTTPS redirect option in the SSL-VPN settings. This option allows the FortiGate to redirect HTTP requests to HTTPS port 443, which is required for Let's Encrypt to validate the domain ownership and issue a new certificate. By enabling this option, the FortiGate will be able to respond to the HTTP challenge from Let's Encrypt and renew the certificate successfully. Reference: https://docs.fortinet.com/document/fortigate/6.4.0/cookbook/103437/inbound-ssl-inspection https://docs.fortinet.com/document/fortigate/6.4.0/cookbook/103438/application-detection-on-ssl-offloaded-traffic
NEW QUESTION # 39
Refer to the exhibit, which shows a VPN topology.
The device IP 10.1.100.40 downloads a file from the FTP server IP 192.168.4.50 Referring to the exhibit, what will be the traffic flow behavior if ADVPN is configured in this environment?
- A. All the session traffic will pass through the Hub
- B. ADVPN is not supported when spokes are behind NAT
- C. Spoke1 will establish an ADVPN shortcut to Spoke2
- D. The TCP port 21 must be allowed on the NAT Device2
Answer: C
Explanation:
D is correct because Spoke1 will establish an ADVPN shortcut to Spoke2 when it detects that there is a demand for traffic between them. This is explained in the Fortinet Community article on Technical Tip: Fortinet Auto Discovery VPN (ADVPN) under Summary - ADVPN sequence of events. Reference: https://community.fortinet.com/t5/FortiGate/Technical-Tip-Fortinet-Auto-Discovery-VPN-ADVPN/ta-p/195698
NEW QUESTION # 40
Which two methods are supported for importing user defined Lookup Table Data into the FortiSIEM? (Choose two.)
- A. FTP
- B. SCP
- C. API
- D. Report
Answer: A,C
Explanation:
User defined Lookup Table Data (LTD) is a feature that allows users to import custom data into FortiSIEM for correlation, reporting, and analysis purposes. Users can create LTD files in CSV format and import them into FortiSIEM using two methods: FTP or API. FTP is a file transfer protocol that allows users to upload LTD files to a designated folder on the FortiSIEM server. API is an application programming interface that allows users to send HTTP requests to upload LTD files to FortiSIEM using RESTful web services. Reference: https://docs.fortinet.com/document/fortisiem/6.4.0/administration-guide/19662/user-defined-lookup-table-data
NEW QUESTION # 41
You are running a diagnose command continuously as traffic flows through a platform with NP6 and you obtain the following output:
Given the information shown in the output, which two statements are true? (Choose two.)
- A. Enable HPE shaper for the NP6 will change the output
- B. There are packet drops at the XAUI.
- C. Enabling bandwidth control between the ISF and the NP will change the output
- D. Host-shortcut mode is enabled.
- E. The output is showing a packet descriptor queue accumulated counter
Answer: B,E
Explanation:
The diagnose command shown in the output is used to display information about NP6 packet descriptor queues. The output shows that there are 16 NP6 units in total, and each unit has four XAUI ports (XA0-XA3). The output also shows that there are some non-zero values in the columns PDQ ACCU (packet descriptor queue accumulated counter) and PDQ DROP (packet descriptor queue drop counter). These values indicate that there are some packet descriptor queues that have reached their maximum capacity and have dropped some packets at the XAUI ports. This could be caused by congestion or misconfiguration of the XAUI ports or the ISF (Internal Switch Fabric). Reference: https://docs.fortinet.com/document/fortigate/7.0.0/cli-reference/19662/diagnose-np6-pdq
NEW QUESTION # 42
Refer to the exhibits.
The exhibits show a FortiMail network topology, Inbound configuration settings, and a Dictionary Profile.
You are required to integrate a third-party's host service (srv.thirdparty.com) into the e-mail processing path.
All inbound e-mails must be processed by FortiMail antispam and antivirus with FortiSandbox integration. If the email is clean, FortiMail must forward it to the third-party service, which will send the email back to FortiMail for final delivery, FortiMail must not scan the e-mail again.
Which three configuration tasks must be performed to meet these requirements? (Choose three.)
- A. Apply the Catch-AII profile to the ASinbound profile and configure an access delivery rule to deliver to the 100.64.0.72 host.
- B. Change the scan order in FML-GW to antispam-sandbox-content.
- C. Create an IP policy with a Source value of 100. 64 .0.72/32, enable precedence, and place the policy at the top of the list.
- D. Create an access receive rule with a Sender value of srv. thirdparcy.com, Recipient value of *@acme.com, and action value of Safe
- E. Apply the Catch-Ail profile to the CFInbound profile and configure a content action profile to deliver to the srv. thirdparty. com FQDN
Answer: B,C,E
Explanation:
A is correct because the scan order must be changed to antispam-sandbox-content in order for FortiMail to scan the email for spam and viruses before forwarding it to the third-party service.
B is correct because the Catch-All profile must be applied to the CFInbound profile in order for FortiMail to forward clean emails to the third-party service.
E is correct because an IP policy must be created with a Source value of 100.64.0.72/32 in order to allow emails from the third-party service to be delivered to FortiMail.
The other options are not necessary to meet the requirements. Option C is not necessary because the access receive rule will already allow emails from the third-party service to be received by FortiMail. Option D is not necessary because the Catch-All profile already allows emails to be delivered to any destination.
Here are some additional details about integrating a third-party service into the FortiMail email processing path:
The third-party service must be able to receive emails from FortiMail and send them back to FortiMail.
The third-party service must be able to communicate with FortiMail using the SMTP protocol.
The third-party service must be able to authenticate with FortiMail using the SMTP AUTH protocol.
Once the third-party service is integrated into the FortiMail email processing path, all inbound emails will be processed by FortiMail as usual. If the email is clean, FortiMail will forward it to the third-party service. The third-party service will then send the email back to FortiMail for final delivery. FortiMail will not scan the email again.
NEW QUESTION # 43
What is the benefit of using FortiGate NAC LAN Segments?
- A. It provides support for IGMP snooping between hosts within the same VLAN
- B. It allows for assignment of dynamic address objects matching NAC policy.
- C. It provides physical isolation without changing the IP address of hosts.
- D. It provides support for multiple DHCP servers within the same VLAN.
Answer: B
Explanation:
FortiGate NAC LAN Segments are a feature that allows users to assign different VLANs to different LAN segments without changing the IP address of hosts or bouncing the switch port. This provides physical isolation while maintaining firewall sessions and avoiding DHCP issues. One benefit of using FortiGate NAC LAN Segments is that it allows for assignment of dynamic address objects matching NAC policy. This means that users can create firewall policies based on dynamic address objects that match the NAC policy criteria, such as device type, OS type, MAC address, etc. This simplifies firewall policy management and enhances security by applying different security profiles to different types of devices. Reference: https://docs.fortinet.com/document/fortigate/7.0.0/new-features/856212/nac-lan-segments-7-0-1
NEW QUESTION # 44
......
Fortinet NSE8_812 certification exam is intended for individuals who want to demonstrate their expertise in Fortinet security solutions and become a certified Fortinet Network Security Expert (NSE). Fortinet NSE 8 - Written Exam (NSE8_812) certification validates the skills and knowledge required to design, implement and manage advanced security solutions using Fortinet's security products.
NSE8_812 [Jan-2024] Newly Released] NSE8_812 Exam Questions For You To Pass: https://actualtests.torrentexam.com/NSE8_812-exam-latest-torrent.html
